1/13/2023 0 Comments Locker shelfUse a measuring tape to find the inside width of your locker. This will be the size of the inside of your locker. If not you need to cut your chosen material to the size needed for your shelf. Step 5: If you have a shelf prepared in the dimension of your locker you can move onto Step 6. Alternatively, if you don’t want to drill into your locker, you could use double sided adhesive pads to stick the wood into the locker, but be aware the shelf will not be able to support as much weight compared to screwing the wood in.Screw a screw through each drilled hole (from the outside of the locker, drilling into the wood inside the locker) & screw the piece of wood into place until it is tight. Step 4: Hold the wood (or if you have someone helping you ask them to) evenly against the side of the locker so that the holes you drilled are in the centre of the wood.This is what the shelf is going to rest upon so ideally they won’t be large. Step 3: Cut two pieces of wood to fit inside the locker walls.Go at least ¼ of an inch below the line to give way for the thickness of the material used on the shelf otherwise the shelf will sit above your original marking. Step 2: Now drill two holes on each side of the locker slightly below the line.Make sure that the mark is the same level around or your shelf will slant. Step 1: Inside your locker, mark the level that you want the shelf to go on both sides of the locker.So another reason to pull out the router table and a 3/8” round-over bit.To install a shelf into your locker you will need: the shelf, a drill, screws (or double sided adhesive pads), wood & measuring tape. It can “chip” if you hit the edge, but usually splits like the layered biscuits you make from those pressurized cans. This will deflect the impact of the skateboard helmet allowing the back of the locker to take the brunt of the damage and I won’t have to break out my table saw, router…blah, blah, blech again to make some more. Since the kids will be slamming stuff into them, I thought it would be good to round-over the front of each shelf, top and bottom. I planned to leave one or two lockers without any shelves, but have the finished shelves stored in case we changed our mind later. So some lockers could have two shelves, some have one shelf. So the shelf fit, and I cut a bunch more, roughly 12. When cut the dust is very fine, and combined with the resins, your lungs won’t be happy breathing this stuff. MDF is made from wood pulp and fibers, bound by resins and compressed to form the sheet. Speaking of…wear your safety glasses, and most certainly wear a respirator while cutting MDF. Now…all together…measure twice, cut once.Īnd cut only one and test fit it before making a bunch of sawdust. The pin fit perfectly in the factory shelf hole. I had a bunch of those shelf pins, or shelf supports, with a hole so you could fasten the support with a screw. More on MDF in the steps, now back to building shelves. I’ve been using it for over 25 years, when you had to special order it from a lumber supplier. I checked the stockpile™ and found some ¾” MDF. I didn’t have the time to bend up some metal on the brake, paint it, and the like. It was obvious they were some for shelves, metal shelves, that would be riveted in place. I noticed the lockers had quite a few holes punched from the factory for the many configurations they offer. Pretty much the same stuff I use to put in mine at school. They’re in the boys’ room and had the potential to hold, well…skateboards, pads, helmets, toy guns, army men, dirty socks, superhero capes, food they didn’t like, one or both of the cats, stinky shoes…y’know…boy’s stuff. So I have a bank of three lockers, three high. Or it would just hold your skateboard and a rat bones poster. Or you’d put pictures up in it of your girl. Or talk to a buddy about some girl three lockers down. Or *gasp* you’d share your locker with a girl. Or you’d meet your girl there at your locker. The pocket knife you found.Īnd she couldn’t go through it like your sock drawer. You could stash stuff you came across that didn’t (or shouldn’t) make it home for Mom to find. Don’t you remember lockers were like your first, very own ‘personal’ space? I was one of the few that used them at that agency. Nah, it was probably easier for them to have me load them in my truck by myself and get them outta there. I’d like to think it was a gesture recognizing the many, many, many, many hours I spent working overtime there. They were downsizing, the lockers wouldn’t fit in the new space, and I was the lucky recipient. A little over a year ago I was given some lockers…school lockers…that were used for employee storage at the agency I worked at.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |